Recent content by Dee87

  1. D

    Emmc Slower Mode Picofly

    It depends on the switch, some work with 47ohm and some need 100ohm , every install I do now gets 100ohm since I had the first issues
  2. D

    Installers in the EU / Europe

    Looking good How u like the emmc pinout adapters?
  3. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Come on bro u been long enough here to know the answer to that Xd
  4. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    DAT 0 adapters Tend to bend when they warm up some more some less It's def your adapter had a few people come to me with the same issue, after setting a permanent Dat0 and reballing the issue never came back
  5. D

    Emmc Slower Mode Picofly

    Na dont ask there its a clone won't get help there. But u answered it yourself , you gotta change the resistors ;) On the picture main board above the flex connector, there are 3 resistors these should be the ones. now u need to find the correct resistors use a multimeter and find the resistors...
  6. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yeah that was Probally Me Xd Saidly that is Very true all the other installers that I know around here only use Adapters,I Mean okay if u use a Proper one and install it Properly they might work. But for them its just fast cash and I had a lot of people from them reach out to me cause they...
  7. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Why in the hell would u add UV mask directly under the emmc. When u set a dat0 point always us UV mask above the emmc and not directly underneath, if u do that ur gonna have issue cause the emmc will never sit properly instead its gonna lay on the UV mask
  8. D

    Picofly AIO Thread

    It has to be named payload. There is no other led on the switch so the picofly Led is the only one u can look at :-)
  9. D

    Hacking OLED HWFLY Clone won't boot OFW?

    How do u have the idea that the ribbon cable is the fault that some consoles need a 100ohm resistor? I can tell u that is bullshit cause I never use ribbon cables........ If u think ribbon cables are a scam then u should the same about the trash clone rp2040 chips and stick with the boards...
  10. D

    Hacking OLED HWFLY Clone won't boot OFW?

    why dont u just take a waveshare rp2040 tiny and install it instead of the hwfly clone. all other rp2040 are just clones and the firmware is written for the waveshare rp2040 zero/tiny. ive done over 200 installs just with the original Picoflys and never had any issues. i mean some devices still...
  11. D

    Hacking OLED HWFLY Clone won't boot OFW?

    Yepp that's one of those rp2040. Should be those resistors , the size is 0201 I would say. U can also add another 47 ohm some where down the line. It all depends how u prefer doing it
  12. D

    Hacking OLED HWFLY Clone won't boot OFW?

    What kinda clone? If its rp2040 try replacing dat0 and cmd 47ohm resistors with 100ohm resistors that should solve the problem. Some switches need 100ohm instead of the preinstalled 47ohm
  13. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Check YouTube for switch emmc permanent dat0 / emmc reballing
  14. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    u cant buy it . u take ur emmc off , set a permanent dat0 point i use Solder repair pads for that. then u reball ur emmc and solder it back on
  15. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    this has nothing to do with resistor issues. its just a switch thing some need 100ohm do run properly. is u put your switch back together completly befor testing then it is ur own fault !!! with a zero and a tiny u know its works properly with this firmware. no one has any diagramms from the...
See more
General chit-chat
Help Users
  • No one is chatting at the moment.
    K3Nv2 @ K3Nv2: Hawaii played it smart and said we're too hot for this land