Recent content by P4RI4H

  1. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    Yes glare from my camera is automatically a bridge. I did these with a microscope, there is no bridge. Fuck off. Fucking toxic piece of shit. Sent from my SM-N986U using Tapatalk
  2. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    I already did that you moron. Don't you have a hobby? Oh wait, Nintendo sent you a c&d and I'm still making money. Must be with all that extra time you grief people online with 2 accounts to pat yourself on the back. And if you're such the genius, surely you know what's wrong instead of...
  3. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    Go fingerbang your bf Izy. I know my soldering is solid and my bank account agrees. How immature and toxic. Sent from my SM-N986U using Tapatalk
  4. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    I only have a multimeter. The v2 boots atmosphere and displays to a TV if docked. Sent from my SM-N986U using Tapatalk
  5. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    What points should I test? Backlight only, correct. Sent from my SM-N986U using Tapatalk
  6. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    Soldering isn't the issue or else my failure rate would be higher than 2 out of ~40. The soldering is fine and unless youre s-tier, i dont want to hear that when its not the problem. And that's VERY constructive and conducive to the question at hand. What a great atmosphere we have here where...
  7. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    Before you wanna be a dick, I'm using Flux and a Weller soldering station OR a pinecil depending. If you aren't gonna be helpful, fuck off. Not my fault you're Butthurt over your c&d. Says "janky" but then has this posted like all the solder is better and not even fused to the shield.
  8. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    Ive done them all a couple times before without issue. I even sell premodded OLEDs on the side and Ive never had an issue except beeding to redo a dat0. With Core and Lite, I've never had this issue until these 2. I can assure beyond a doubt that there are no shorts with the core as it's just...
  9. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    I'm at my goddamn wits end with these things. Installed a HWFLY Lite and Core V1 for a FoaF, and now neither displays anything on LCD upon boot. The LCD cable was never unplugged and the batteries on both were unplugged immediately. If it was one time I would chalk it up to chance damage bit...
  10. P4RI4H

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    So last night I decided to clean up my wiring, and I trimmed and re-soldered everything on the Trinket. The random vol+ stopped. I have NO IDEA why because all that changed were wire lengths. I'll keep this in mind if it starts again. Thanks! Sent from my SM-N986U using Tapatalk
  11. P4RI4H

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Hey everyone, things are getting wonky again for me here. I had an issue before of Vol+ triggering that was solved with kapton tape. Well today I was re-shelling my switch and decided to hook up the joycon strap because I read that a dead battery+auto rcm can hurt the charge chip. I added joycon...
  12. P4RI4H

    OLED, permanent dat0, inconsistent boots?

    @OrganixXx No, I hadnt posted on twitter, but i did ask about voltages on reddit with Hynix. I have it permanently attached with reflow and its the 2 anchor version. Tried multiple adapters and always get same 2 readings .2 v apart. @randy_w yes, purple>orange like when it starts...
  13. P4RI4H

    OLED, permanent dat0, inconsistent boots?

    Recently installed HWFLY in OLED, The dat0 point always gets 2 values and always exactly .2v difference. Was told that with SK Hynixemmc, this is normal as long as I get successful glitches. However, training took ungodly long, to the tune of ~4 hours. Ive never been unable to get a single .6xx...
  14. P4RI4H

    OLED Hekate slow with SD

    I recopied the hekate payload files and it fixed the issue. Obviously they didnt copy correctly when extracted to SD for whatever reason.
  15. P4RI4H

    OLED Hekate slow with SD

    I just recently installed a HWFLY chip in my OLED, and without SD card, my switch boots instantly (<5s) and says no SD card which is expected. When I put payload.bin on an sd card and insert it, it takes nearly 30 seconds to boit to the attached screen and does nothing else. Any ideas...
See more
General chit-chat
Help Users
    The Real Jdbye @ The Real Jdbye: don't mind me, just liking all of SDIO's posts, they deserve it for...