Recent content by Raugo

  1. R

    Installing large XCI

    Yes, you can.
  2. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    You don't need to do it if you don't want but I think that you need a better printer to make a better fake cover.
  3. R

    Picofly AIO Thread

    If you have 2.5 you can't flash with pikotool.
  4. R

    Picofly AIO Thread

    I tried a lot of things and still have the problem wht the boot0/boot1 and slow mode of the emmc. I maked a emummc and can launch HOS from it. Is dangerous to leave it at this for the moment? I'm really tired and want to rest.
  5. R

    Picofly AIO Thread

    I replaced the wires with new ones shorted and now is worst, when I try to launch HOS with vol+ and vol- mpt sjpw amything at all except one time that show pink screen. It is possible that i damaged the emmc? Edit: I mounted the emmc in windows with hekate and can see the content and appear to...
  6. R

    Picofly AIO Thread

    Is strange, now I get this error when I try to launch HOS from hekate, I tried earlier and worked. I'm using 2.64 firmware in a fresh install. If I desolder the Dat0 the conosle launch hos without problem.
  7. R

    Picofly AIO Thread

    Ok, is all installed and get the no sd card screen but I have a problem, if I boot with vol- + vol+ to boot stock the console get stuck in a black screen after the nintendo logo.
  8. R

    Picofly AIO Thread

    Oh right, is a mariko normal (no oled no lite) @rehius that is not an option now because I have 3 points in the emmc now and to solder in the connector I would need to remove the emmc
  9. R

    Picofly AIO Thread

    Any other alternative point for th3 3.3v? I used the one from the emmc but it has come loose and I don't want to remove the emmc again so as not to lose the reset too and the one next to the memories is difficult because I have the chip right next to it.
  10. R

    Picofly AIO Thread

    I have a doubt about the 3.3v in the emmc board, in the picture appear to be shorted is that correct?
  11. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    19,5 Ohm with the lowest resistance. Is a relieve because I had a lot of problem soldering the second mosfet. Thank you
  12. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    Anyone with the cpu flex can tell me what value get the multimeter in continuity mode in the solder points? To check if I have solder mine well. I get 0001 and 0015 in the two points of the two mosfets
  13. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    No, the upgrade feature was added in the 2.6 version.
  14. R

    Homebrew WIP [Official] switch-lan-play

    ldn.mitm convert the ad-hoc (connection between consoles without using a lan) to a lan connection. Without it you can't use lan-play in some games.
  15. R

    Unpatched Switch Not Going Into Recovery Mode

    You don't need to change SD, PC,, USB etc you don't need any of this to enter to rcm you need it to send the payload. Check if the vol+ works in HOS and if the joycon is recognied attached (to discard a problem with the rail) It doesn't matter, patched switches can enter to rcm too.
See more
General chit-chat
Help Users
  • No one is chatting at the moment.
  • K3Nv2 @ K3Nv2:
    https://www.newegg.com/p/0D9-002V-0...=snc-social-_-sr-_-0D9-002V-00AA1R-_-05202024
  • SylverReZ @ SylverReZ:
    @mthrnite, Cheetah Girls, the sequel to Action 52's Cheetah Men.
     +2
  • Psionic Roshambo @ Psionic Roshambo:
    Pokemon Black I played that one a lot
  • K3Nv2 @ K3Nv2:
    Honestly never messed with Pokémon on ds much
  • mthrnite @ mthrnite:
    I played pokemon once, was bored, never tried again
  • Psionic Roshambo @ Psionic Roshambo:
    Oh Dragon Quest IX
  • K3Nv2 @ K3Nv2:
    Spent like 5 hours on switch one never touched it again
  • Psionic Roshambo @ Psionic Roshambo:
    Sentinel of the stary skies
  • K3Nv2 @ K3Nv2:
    Ds is 20 years old this year
  • Psionic Roshambo @ Psionic Roshambo:
    So MJ no longer wants to play with it?
  • K3Nv2 @ K3Nv2:
    He put it down when the 3ds came out
  • K3Nv2 @ K3Nv2:
    https://youtube.com/shorts/eTlZ0qcSZf4?si=0vpkdIWplaLMFVqv
  • K3Nv2 @ K3Nv2:
    https://youtu.be/40XQ8L9wsCA?si=GzpPBaHQQLU0plt_ Neat
  • SylverReZ @ SylverReZ:
    @K3Nv2, RIP Felix does great videos on the PS3 yellow-light-of-death.
  • Jayro @ Jayro:
    Eventhough the New 3DS XL is more powerful, I still feel like the DS Lite was a more polished system. It's a real shame that it never got an XL variant keeping the GBA slot. You'd have to go on AliExpress and buy an ML shell to give a DS phat the unofficial "DS Lite" treatment, and that's the best we'll ever get I'm afraid.
     +1
  • Jayro @ Jayro:
    The phat model had amazingly loud speakers tho.
     +1
  • SylverReZ @ SylverReZ:
    @Jayro, I don't see whats so special about the DS ML, its just a DS lite in a phat shell. At least the phat model had louder speakers, whereas the lite has a much better screen.
     +1
  • SylverReZ @ SylverReZ:
    They probably said "Hey, why not we combine the two together and make a 'new' DS to sell".
  • Veho @ Veho:
    It's a DS Lite in a slightly bigger DS Lite shell.
     +1
  • Veho @ Veho:
    It's not a Nintendo / iQue official product, it's a 3rd party custom.
     +1
  • Veho @ Veho:
    Nothing special about it other than it's more comfortable than the Lite
    for people with beefy hands.
     +1
  • Jayro @ Jayro:
    I have yaoi anime hands, very lorge but slender.
  • Jayro @ Jayro:
    I'm Slenderman.
  • Veho @ Veho:
    I have hands.
  • Veho @ Veho:
    king-shark-hand.gif
    +1
    Veho @ Veho: +1