Search results

  1. nalex7752

    Help with the Instinc v6 post-installation

    Yeah, totally! I mean, im not new to soldering but its my first time doing something on a switch so could absolutely be! Anyway, thanks again, ill check another time my soldering and ill post it back if i find any other problem. But, do i need to update the firmware on the chip? Is there a...
  2. nalex7752

    Help with the Instinc v6 post-installation

    isnt the B point actually just a GND? Should I try another ground on the board?
  3. nalex7752

    Help with the Instinc v6 post-installation

    I got the chip off AliExpress, but I don't know if it's preflashed. I found a guide here for flashing, which involves soldering directly onto the chip. However, I have a microUSB breakout that I believe could be used for updating. Is it as simple as plugging in the 'dongle' and dragging and...
  4. nalex7752

    Help with the Instinc v6 post-installation

    I read that this modchip quality isnt that great and to pay attention to not add to much solder on the chip pads as it could easily short on the ground of the chip. Btw thanks, ill redo all of my soldering.
  5. nalex7752

    Help with the Instinc v6 post-installation

    Yep, I did the installation I'm not at home at the moment and I only got this image.
  6. nalex7752

    Help with the Instinc v6 post-installation

    Hi all, i got this Oled with the instinct v6 installed but i cant recognize the led sequence. tested all the points, the readings are: 3.3v .718 - D .632 - A .549 - C .553 - On the D point i cant get a reading, but i read that some multimeter (like mine cheap AF) cant get a good measurement, i...
  7. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    Xeno was the problem, replaced with a clone one and it works perfectly. You can close the thread. Thanks all!
  8. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    avrdude command with the reset grounded
  9. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    Did it, but, is it normal that avrdude wont recognize the chip? The power led wont event turn on.
  10. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    Currently trying to reflash it via avrdude but without luck. I've found this site https://kyleglisso3.wixsite.com/moddedgear/mods but i can't get the program find the Atmel. I know that the solder aren't the best this time maybe because it's pretty late. I'm gonna try again tomorrow, let's see...
  11. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    the pal game that i have is working fine, the ntsc-j or the swiss dvd did not boot at all
  12. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    already tried, solid red led. nothing else :(
  13. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    I think im missing something, how do i load Swiss to reflash the chip if i even cant get it to glitch the dvd drive? Sorry if the question sounds really dumb 😅
  14. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    So i need an SdGekko to load the file that need to be flashed on the Xeno, right? Can i use the sd2sp2?
  15. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    thanks but i was reading also this https://github.com/vingt-2/xenogcfork/ and its mentioned on both site that i need a programmer, at home i've an Arduino uno ( i was reading how to use it as an ISP flasher ), a Rasperry Pico and a StLink used for the Game and Watch. what would be the best to do...
  16. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    Thats exactly what i wrote at the seller, i think the chip its corrupted or not flashed correctly. How can i reflash it?
  17. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    Tried the japanese one, console refuses to boot. I'm gonna desoldering it again, let's see if the third is the right one
  18. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    nope, already contacted the seller but he told me that he can refound me only if the modchip wouldnt lights up :/ I've ordered another one, delivery estimated from 1/2 weeks unfortunately. I think i have to wait, sigh
  19. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    Yep, the via starting from the central hole to the top right pad are connected. Im sure because ive cleaned all the pads multiple times and, except for the pad 1, its all good!
  20. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    Except fot the power and the gnd ( bottom left pin, ive lifter it up while desoldering the chip from the direct install; the 5v is taked out from that little smd ) everything is soldered following the schematics.
General chit-chat
Help Users
    ZeroT21 @ ZeroT21: You need better couch potatoes la +1