Search results

  1. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    I've got turqoise 2021 switch lite with picofly + toshiba emmc and it glitches in about 1.5 seconds
  2. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thank you, it shows 0.708 ;)
  3. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    i'm attempting to do picofly installment on oled - what resistance should I get between D0 from adapter and metal shielding around emmc? My multimeter shows me 1.84Mega Ohm, is that correct reading to believe D0 adapter is correctly mounted?
  4. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    I'm honestly have no idea also. I asked the same question and I've got following response: When I checked it with multimeter there is no resistance (except multimeter probes ofc) between these points so I believe that's no reason to do so (if there is however I would like to know :) ). Here's...
  5. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    After flash you got red or green blink? Thats may be silly but maybe you forget about GRB/RGB led mode and what you think is green is really red (?)
  6. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    you probably shortcuit some cables. Did you cut metalshield to make place for picofly? Check if it working without it. I initialy didn't cut it and I was having simmilar issue that it was working correctly when I solder it, but when I put the metal shielding back and screw it I got red blink. I...
  7. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    Does rp2040 without WS logo between buttons also works? (left chip)
  8. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    thank you, but why most of the people uses 2 mosfets? Whats the benefit of doing so?
  9. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello, I will try soldering mosfets without flex cable for picofly mod after mosfets come. But I did not know why sometimes on schema there is one mosfet and on the others 2 mosfets. Should I use two IRFHS8342TRPBF or just one is sufficient? Whats the difference when using two mosfets? Also when...
  10. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Is there easy process for dumping nsp from sysMMC to emuMMC? I want to copy some games that I own to atmoshpere to not need to switch between the oses. I can probably do that by creating another emuMMC that will clone current sysMMC (with game that I want), and then copy nsp from that newly...
  11. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Unfortunately no, I dont have hwfly cable at the moment, so I'll buy one and I guess then I'll try again then since I lurked at switchroot discord a little and there are mixed information about if its possible to flash hwfly-nx using hwfly-toolbox on sx chips:
  12. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Sorry if my questions were silly. After "Update SD loader" the same error "Board was not initialized properly" is still present however (after updating I need to wait around 2 minutes to hekate to show up and diode was blinking blue). Do I need also to update firmware in hwfly toolbox? // also...
  13. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I already came across that page, but I dont understand part "If you have hwfly-nx (...)" I believe I dont have "hwfly-nx", my modchip is original sx one: Or maybe you meant that even if my chip is SxT it should have hwfly-nx firmware on it, correct? Can I check somehow what firmware is on it...
  14. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Hello, for the whole time I was thinking I have switch lite with hwfly chip (I bought it from second hand). However after I try to boot L4T (Atmosphere and OFW works perfectly) I've got error "Board was not initialized properly! Hang prevented. Board will reboot in 10s…". After searching a lot...
  15. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Hello, I try to setup lakka to play some retro games. I followed up http://www.lakka.tv/doc/Nintendo-Switch/ but I always get "Board was not initialized properly! Hang prevented" I'm on hekate 6.0.2 + 1.5 atmosphere prelease, and mariko switch. Is thats because I dont have ext4 partition on my...
  16. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I tried your /bootloader/hekate_ipl.ini but i've got error thats atmosphere/kips/loader.kip is missing. Where could I download it with also atmosphere/kip_patches, because when i google for it the things I only found are 404 on github // okay I got it from...
  17. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    yes, I can still boot into OFW, i'm on switch lite with hwfly
  18. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    hmmm, after upgrading OFW to 16.0 and when I'm trying to boot atmosphere on CFW with 15.0.1 I've got: A fatal error occurred when running Fusee. Failed to locate warmboot firmware! I initialy thought that SD card gets formated after update, but when I view in on pc: So I bet emunand is on...
  19. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Probably I described a drift, but in the "Calibrate control sticks" screen, and in games the joysticks works perfectly, only in hekate the cursor is going slightly down, so my bet was that in the HOS there is larger dead zone and in Hekate there is less dead zone. So there aren't magic setting...
  20. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I've received switch with the hwfly, I followed up rentry guide and now I've succesfully booted to the atmoshpere. I've created emuNand and updated OS it to the newest possible version for current atmosphere - 15.0.1. But can I also update OFW on sysnand to 16.0? Those are on separate storages...
General chit-chat
Help Users
    Veho @ Veho: 80s are the new 20s. +1