Search results

  1. S

    eMMC exchange question

    Thank you very much :)
  2. S

    eMMC exchange question

    Hello, unfortunately I haven't found any information about this, so I'm asking here. Is it important when changing an eMMC that it is the same as already installed or can it also be a different one? Installed is a SKhynix H26M74002HMR It is not so easy to find. Is it possible to install...
  3. S

    Switch don't Boot. Only RCM with PC.

    Is it possible that a reball could be enough to make the eMMC work again? Does it make sense to use such an adapter if the eMMC has already been replaced? 1702154619 I would like to buy a new eMMC. Should it be the same as the one already installed? (i.e. the SKhynix) or can it also be a...
  4. S

    Switch don't Boot. Only RCM with PC.

    Is there a possibility to boot in hakate without eMMC?
  5. S

    Switch don't Boot. Only RCM with PC.

    So the only way is to swap the nand?
  6. S

    Switch don't Boot. Only RCM with PC.

    Does anyone else have any ideas what I can look for? How could I find the error? If I am not contacting Dat0 correctly, how could I find out?
  7. S

    Switch don't Boot. Only RCM with PC.

    Okay, then I'll get some other wire for the future. So far, however, everything has gone well with the wire. Thanks for the tip
  8. S

    Switch don't Boot. Only RCM with PC.

    Ah, that's what you mean. could it be that I've got the wrong pin? According to the diode test, I've definitely got something. 1702072985 The wire is awg28. The insulation is slightly thicker.
  9. S

    Switch don't Boot. Only RCM with PC.

    What exactly do you mean by ankors? Sorry, I don't know all the English terms :D
  10. S

    Switch don't Boot. Only RCM with PC.

    Is it possible that the eMMC becomes defective if the Switch is left unused in the docking station for a while? Because the Switch suddenly stopped turning on after it had been in the docking station for a while.
  11. S

    Switch don't Boot. Only RCM with PC.

    I have re-soldered it. Error is still there. 1702071190 That could be possible. I was hoping to find out with Hekate. But I can't even manage to boot into Hekate.
  12. S

    Switch don't Boot. Only RCM with PC.

    I measured the connections I found on the internet and they looked good. Likewise the D0 from the eMMC. Is there an overview of exactly how I can check all the points? (especially D, the one where you have to scratch free) I'll take another picture of the eMMC and add it right away Edit: does...
  13. S

    Hacking Hardware Picofly - a HWFLY switch modchip

    I'm sorry. i've started a own Thread. Thank you :)
  14. S

    Switch don't Boot. Only RCM with PC.

    possibly because of the insulation. but thicker cables usually have lower resistances, don't they? Could it be because of the cables that it doesn't work?
  15. S

    Switch don't Boot. Only RCM with PC.

    these are 2 awg28 cables, what is the maximum resistance?
  16. S

    Switch don't Boot. Only RCM with PC.

    I Install it. *=* No eMMC Block 0 ready (eMMC Initiative failure?) This ist my failure. I Hope you can Help me.
  17. S

    Switch don't Boot. Only RCM with PC.

    Hello, i'm sorry for double Post. I installed a Picofly v5 today (which is similar to the hwfly) but my switch only starts in RCM mode (it already did before the installation). The Picofly flashes short-long-short. Can anyone help me with this problem? I have measured the wiring and...
  18. S

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello, I installed a Picofly v5 today (which is similar to the hwfly) but my switch only starts in RCM mode (it already did before the installation). The Picofly flashes short-long-short. Can anyone help me with this problem? I have measured the wiring and everything seems to be connected...
General chit-chat
Help Users
  • BakerMan
    I rather enjoy a life of taking it easy. I haven't reached that life yet though.
    BakerMan @ BakerMan: this one