Recent content by alecocr20

  1. A

    Instinct nx v6s flashing red

    Hello, I replaced the Instinct V6S with a normal V6 and that fixed the issue I suspect and issue with the chip itself (or maybe the firmware) but now I will keep installing the V6
  2. A

    Updated OFW and Hekate, Blue screen on boot to ofw

    Hello, CFW is still working correctly. Normally blue screen is a corrupted and. Some questions: Do you have a Nand backup? How did you update OFW and how do you boot to OFW?
  3. A

    Is this the correct chip?

    The only difference is the flex cable, the orientation of the capacitors is vertical on V1 horizontal on V2
  4. A

    Hacking [Soldering]What does this behaviour mean?

    If you have a multimeter, you can test if the points are bridged and well connected. The chances of your issues being this are pretty high
  5. A

    Homebrew RELEASE MissionControl: Use controllers from other consoles natively via Bluetooth

    Hello, How do I join the discord server, do I need an invite or be friends with Ndeadly. Sorry pretty new to disccord
  6. A

    Hacking [Soldering]What does this behaviour mean?

    Hi, Pictures are needed to understand what it going on. If the console was getting hot I suppose there was a short somewhere. Try soldering the CPU flex again, use flux and small amounts of solder
  7. A

    Hacking INSTINCT-NX Chip

    I received them last week. The new order are v6 since I never had issues with those, only need careful with the grounding issues
  8. A

    Hacking INSTINCT-NX Chip

    Last v6s I received was blinking red and not glitching once in a while. I replaced it with another one and it worked correctly. Where did you get the info that info that v6s are defective? But it makes sense, I have only installed a couple of them so I though it was bad luck
  9. A

    Instinct nx v6s flashing red

    I tried to debug it with putty. It glitches correctly every time I diagnose and the rest of the info seems ok. That said, it seems to work every time if I don't power on right after but wait a couple of minutes. I'll wait for to try another chip, I don't really think is related to Dat0 but no...
  10. A

    Instinct nx v6s flashing red

    Thank you for the replies It does glitch randomly and fails randomly. I bought some new ones to try a swap. In the meantime, I'll try the putty method. I suppose when is flashing red, I can get the error code? Any place I can find the putty commands available? All I could find was the R to reset
  11. A

    Instinct nx v6s flashing red

    Hello, So yesterday I installed an Instinct nx v6s. It was glitching but also flashing red and going to OFW. I thought I did something wrong with the installation. Removed everything and tried with another console and I have exactly the same result. Also, I flashed the latest firmware that I...
  12. A

    Comparison of modchips on the market

    Hello, it's a RP2040 based chip. I used many of those and the work perfectly so you should be ok
  13. A

    HWFLY RP2040 Lite FPC cable troubles

    Can you post a picture of the whole cable/install? I made the mistake on my first lite install because I didn't turn the flex cable correctly
  14. A

    HWFLY Soldering Help RP2040

    Hello, I am far from being a pro but had some experience from the RGH Xbox 360 time. That said, I installed successfully a couple of chips on Oled/Lite and V1/V2 and I almost broke a V2. Here are my points: - Use quality solder wire and flux, this will make the job way easier - If possible...
  15. A

    DAT0, CMD, and CLK values to check EMMC breakout PCB adapter install?

    Hello, I suppose it should be the same values as when doing the normal installation Diode Mode and between 0.6 and 0.9 volts I would like to know how did you practice, which tools etc. Would like to try this at some point
See more
General chit-chat
Help Users
    Veho @ Veho: Nobody is reading what you post.