ChefVortivask's latest activity
-
ChefVortivask replied to the thread Wii U Stuck on Logo.Sorry for the late reply. This week has been a bit busy for me, but I do intend on doing this soon. I don't mind being a sort of beta tester as I feel a lot of this project has been experimenting and contributing to our knowledge of the Wii U and... -
ChefVortivask replied to the thread Wii U Stuck on Logo.That could work too. Does de_Fuse need to remain installed for any of this? 1714263749 I realized you’re probably referring to ISFShax.
-
ChefVortivask replied to the thread Wii U Stuck on Logo.So at this point, I’m thinking I should probably pivot away from trying to have a working MLC and just use the SATA adapter and hard drive in place of the disc drive. As much as I want to keep the disc drive, it seems like we’ve pretty much...
-
No that is expected. The CLK is driven by the host controler and the Host Controller is also sending the commands to the Card over the CMD line, which is just responding to them. In this case it would still send CMD0 and probe if a card responds.
-
ChefVortivask replied to the thread Wii U Stuck on Logo.So since there’s no card to shake hands with, I would guess that there shouldn’t be anything on the DAT lines. I did notice however that if I tried probing DAT0 and DAT1, but not CLK (no probes connected), the signal looks far weaker than it does...
-
-
ChefVortivask replied to the thread Wii U Stuck on Logo.I guess it was nothing then, but at least I learned something. It’s possible that CMD0 was sent out, but I may not have had the vertical scale set properly or it was just really fast. What about the signals on the DAT lines? Are those expected...
-
ChefVortivask replied to the thread Wii U Stuck on Logo.So I think I may have found the cause of the problem, or at the very least something that should not be happening. I decided to try probing with the oscilloscope with no micro SD card inserted in the slot. I also did not use de_Fuse and removed...
-
-
ChefVortivask replied to the thread Wii U Stuck on Logo.I've never seen CLK go to 3V3. The highest I ever saw was when it went to 2.16 V when trying minute, but normally it is around 1.7 V. I've tried trigger on falling edge and I never captured it going higher than around 2 V. I've also stated this...
-
ChefVortivask replied to the thread Wii U Stuck on Logo.So I've been thinking about this for a couple days now, but is there any chance that the eMMC (the old Hynix one) could be interfering? We know that its CLK and CMD signals are completely cut off due to the pads being torn off, but let's assume...
-
ChefVortivask replied to the thread Wii U Stuck on Logo.So based on all your comments for my oscilloscope traces, it's appearing to me that things seem to be working as expected. Obviously the CLK still isn't reaching 3V3, but it doesn't seem like any particular signal is showing any red flags or...
-
ChefVortivask replied to the thread Wii U Stuck on Logo.I didn't have a chance to try it out yesterday, but I did today. There definitely is some different activity on CLK as booting into the minute menu happens. There's initially this wave that may be square, but it's rise and fall times are so fast...
-
-
ChefVortivask replied to the thread Wii U Stuck on Logo.Sorry. It seems I was a little unclear and confusing in my wording before. I was also talking about CLK, not CMD. I only mentioned CMD when I referenced what we were originally thinking of trying (pull-up resistor between CMD and 3V3). I...
-
ChefVortivask replied to the thread Wii U Stuck on Logo.If that’s the case, and it does make some sense based on what you said, would there be any fix for that? Originally we were going to put in a pull up resistor to drive it high, but if we need to drive it low, I’m assuming the same method of just...
-
ChefVortivask replied to the thread Wii U Stuck on Logo.I soldered in a 1 kohm resistor between the 3V3 pad and the CLK castellated via. It doesn’t look the prettiest, but the multimeter seems to show everything to be fine. I tried probing with the oscilloscope again and it doesn’t look like anything...
-
ChefVortivask replied to the thread Wii U Stuck on Logo.I can give that a shot. I’m assuming it’ll be like what we had planned for CMD and I’ll be putting the resistor between CLK and 3V3? For the CLK point, I can’t use the pad on the NAND-AID right? It would either have to be the castellated via or...
- No one is chatting at the moment.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
@
BigOnYa:
I haven't played my Switch n a month or so, just been playing Xbox, and just picked to play lil and Damn that A and B, X and Y being reversed always gets me. -
@
slaphappygamer:
I havent played my xbox360 is a couple of years. My switch got much use the last few days. Tears of The Kingdom is great+1 -
@
BigOnYa:
I agree Tears is great. I even played thru it completely twice. I've been hooked on playing thru Fallout 4 again though, after they released the next gen version for Series S/X. Is pretty cool update.
-
-
@
NinStar:
tears of the kingdom is not the type of game I would ever intentionally start over unless it had a new game plus -
@
NinStar:
because I already got burned out with breath of the wild, which for the most part is essentially the same game, and then again with master mode, which doesn't work as a new game plus (that always felt bizarre to me)
-
-
-
