Recent content by wikisa

  1. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    I've got turqoise 2021 switch lite with picofly + toshiba emmc and it glitches in about 1.5 seconds
  2. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thank you, it shows 0.708 ;)
  3. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    i'm attempting to do picofly installment on oled - what resistance should I get between D0 from adapter and metal shielding around emmc? My multimeter shows me 1.84Mega Ohm, is that correct reading to believe D0 adapter is correctly mounted?
  4. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    I'm honestly have no idea also. I asked the same question and I've got following response: When I checked it with multimeter there is no resistance (except multimeter probes ofc) between these points so I believe that's no reason to do so (if there is however I would like to know :) ). Here's...
  5. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    After flash you got red or green blink? Thats may be silly but maybe you forget about GRB/RGB led mode and what you think is green is really red (?)
  6. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    you probably shortcuit some cables. Did you cut metalshield to make place for picofly? Check if it working without it. I initialy didn't cut it and I was having simmilar issue that it was working correctly when I solder it, but when I put the metal shielding back and screw it I got red blink. I...
  7. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    Does rp2040 without WS logo between buttons also works? (left chip)
  8. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    thank you, but why most of the people uses 2 mosfets? Whats the benefit of doing so?
  9. W

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello, I will try soldering mosfets without flex cable for picofly mod after mosfets come. But I did not know why sometimes on schema there is one mosfet and on the others 2 mosfets. Should I use two IRFHS8342TRPBF or just one is sufficient? Whats the difference when using two mosfets? Also when...
  10. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Is there easy process for dumping nsp from sysMMC to emuMMC? I want to copy some games that I own to atmoshpere to not need to switch between the oses. I can probably do that by creating another emuMMC that will clone current sysMMC (with game that I want), and then copy nsp from that newly...
  11. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Unfortunately no, I dont have hwfly cable at the moment, so I'll buy one and I guess then I'll try again then since I lurked at switchroot discord a little and there are mixed information about if its possible to flash hwfly-nx using hwfly-toolbox on sx chips:
  12. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Sorry if my questions were silly. After "Update SD loader" the same error "Board was not initialized properly" is still present however (after updating I need to wait around 2 minutes to hekate to show up and diode was blinking blue). Do I need also to update firmware in hwfly toolbox? // also...
  13. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I already came across that page, but I dont understand part "If you have hwfly-nx (...)" I believe I dont have "hwfly-nx", my modchip is original sx one: Or maybe you meant that even if my chip is SxT it should have hwfly-nx firmware on it, correct? Can I check somehow what firmware is on it...
  14. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Hello, for the whole time I was thinking I have switch lite with hwfly chip (I bought it from second hand). However after I try to boot L4T (Atmosphere and OFW works perfectly) I've got error "Board was not initialized properly! Hang prevented. Board will reboot in 10s…". After searching a lot...
  15. W

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Hello, I try to setup lakka to play some retro games. I followed up http://www.lakka.tv/doc/Nintendo-Switch/ but I always get "Board was not initialized properly! Hang prevented" I'm on hekate 6.0.2 + 1.5 atmosphere prelease, and mariko switch. Is thats because I dont have ext4 partition on my...
See more
General chit-chat
Help Users
    Psionic Roshambo @ Psionic Roshambo: https://m.youtube.com/watch?v=SFpbRlIfowM&pp=ygUnQW5kIG5vIExpdHRsZSB0aW1teSBnbHVlZCB0byBoaXMgY3Jp...