Hacking 2 Red Lights?

[c4p0]

I was trying to rgh 1.2 hack my phat jasper, everything was going good i booted into xell but now everytime I try and boot the console I just see 2 red lights immediately. Did i break my console ? Is this recoverable?

 

[DinohScene]

Remove the glitch chip and flash a stock NAND.
See if it boots.

If it does, resolder everything and flash a freshly hacked NAND to the console.

 

[c4p0]

Remove the glitch chip and flash a stock NAND.
See if it boots.

If it does, resolder everything and flash a freshly hacked NAND to the console.

Thanks for the fast reply i will try it and report back!

 

[DinohScene]

I doubt it's the 360 but it's just to rule it out, removing the chip would be a good thing to do.

 

[c4p0]

I doubt it's the 360 but it's just to rule it out, removing the chip would be a good thing to do.

am i screwed if i didn't back up my nand?

 

[DinohScene]

If you got your CPU key and Keyvault, you can build a new stock NAND.
If you don't (and seeing you don't have a NAND backup) it's going to be extremely difficult to do that.

 

[c4p0]

If you got your CPU key and Keyvault, you can build a new stock NAND.
If you don't (and seeing you don't have a NAND backup) it's going to be extremely difficult to do that.

so yea... screwed

 

[DinohScene]

2RL usually means overheating (on a stock 360)

Humm, are you still able to boot into XeLL?
By pressing Eject or powerbutton?

 

[c4p0]

2RL usually means overheating (on a stock 360)

Humm, are you still able to boot into XeLL?
By pressing Eject or powerbutton?

no i get no display at all. like as soon as i boot its and instant 2 red lights. it booted into xell once then it wasn't booting at all anymore so i figured one of my points wasn't on correctly, so i chose an alternate point for my orange wire. i could have possibly damaged my board?

 

[DinohScene]

Could you post some high resolution and high quality photos of the solderjob?

 

[c4p0]

Could you post some high resolution and high quality photos of the solderjob?

well ive unsoldered everything now that i figured it was dead. when i get home im gonna see what i can do about my nand and update you. Thanks for the advice

 

[DinohScene]

No prob~

 

[c4p0]

No prob~

Okay sorry it's taken me so long to get back to you but I've been a bit busy. Anyways turns out I still have my cpu key because I took a picture of it when xell booted up. Now how do I go about getting to or finding this keyvault you speak of ?

 

[DinohScene]

Well, seeing you have your CPUkey, you can build a NAND from scratch, even with a banned keyvault.
However, you will need to have your glitch hardware in place (if it glitches to XeLL again, it'll glitch into a hacked NAND)
Unfortunately, I can't give out keyvaults (warez)
So you'll have to get ahold of those for yourself.

 

[c4p0]

Well, seeing you have your CPUkey, you can build a NAND from scratch, even with a banned keyvault.
However, you will need to have your glitch hardware in place (if it glitches to XeLL again, it'll glitch into a hacked NAND)
Unfortunately, I can't give out keyvaults (warez)
So you'll have to get ahold of those for yourself.

I would have to set the glitch chip back up build a new nand write it the the console then hope that it boots ?

 

[DinohScene]

Yep.

Now, I don't know what you did (if you already overwritten the NAND or not) but if you only flashed the ECC (to boot into XeLL) then you should even be able to dump your NAND and extract the keyvault from it.
If not, searching for a Keyvault will be the thing to do.

 

[c4p0]

can anything be done with the fuseset?

 

[DinohScene]

You can get your CPU key from it to decrypt the NAND.
Other then extracting the KV (if it hasn't been banned), it's useless.