colleagues, the chip turns blue and turns red, start the original console, how could it be solved, thanks for the help
They're all basic electronics parts, nothing special. Ebay, amazon, maker shop around the corner all should have this stuff.
Looking into parts. Would this resistor work fine, size-wise, for a Switch Lite? The AIO thread suggests an SMD 8050 resistor size but I can't seem to find that anywhere.
Also, would I need to update the firmware on the RP2040? If so, how would I do that? The USB port will be removed, so I'm a little stumped in this area. Would it be better to get an RP2040-One to simplify this?
Also, would I need to update the firmware on the RP2040? If so, how would I do that? The USB port will be removed, so I'm a little stumped in this area. Would it be better to get an RP2040-One to simplify this?
sure they would work but instead of looking for 8050 might wanna search for 0805 :-)
nice just orderd it so i can reball the oled emmc and set a permanent dat 0 pin
but befor i do that i will try first on some defektive emmcs and then try one extra thats works before i go the the oled :-)
The AIO thread says 8050, so that's what I searched:
Probably worth an edit to prevent future confusion.
Either way, thank you! Found this listing.
Post automatically merged:
Another question: what is the reason for removing the 3.3V regulator from the RP2040? If I'm to update the firmware later, wouldn't I need this?
although @rehius said it is ok, i think that a melting point of 138°C is a bit low for this kind of chip also considering how tight things are packed inside switch (and the temperature levels inside).
Anyway, i'm in way an expert on the matter but I thought it was worth giving it a second look.
@Adran_Marit
can u change 8050 smd to 0805 please
thank uthat one looks better
to save some space , yes if u want to over usb u should leave it
i think when fw 2.6 is released u can do that over hekate so for now leave it till the update is out
Last edited by Dee87,
Ah, I'll be able to update using the SD card? That works perfectly then. I'll leave it until I know for sure, thank you!i think afte fw 2.6 is released u cn do that over hekate so for now leave it till the update is out
Attachments
what firmware did u flash ?
i had the same issue
flash the firmware from https://github.com/Ansem-SoD/Picofly/tree/main/Firmwares
first flash 2.5nw.uf2 then flash unlock uf2
what atmosphere version did u try ?
With such melting point it's much easier to solder eMMC back, no damage due to overheating, less PCB bend.
Commonly such high temperature is unreachable (I highly doubt you can get your eMMC even up to the 60°C).
Similar threads
-
@
AngryCinnabon:
anything that offers trump an opportunity to become an actual dictator
is bad in my book, i could care less if it wasn't for that... -
-
-
-
-
@
Psionic Roshambo:
@BakerMan, yeah that's about the only reason I would vote for Trump over Biden.+1 -
-
-
@
Veho:
I don't give a fuck about what happens to America but I would like it if your shit didn't spill out on the rest of the world, thank you.+3 -
-
@
AncientBoi:
I give a fuck about what happens to America but I would like it if our shit didn't spill out on the rest of the world, thank you.+2 -
-
@
Psionic Roshambo:
@Veho, didn't need any news. Just going to the store and buying groceries is a constant reminder.
-
-
-
@
Veho:
Reminded that every single price gouging law was blocked by republicans because "muh gubmint overreach"?
-
-
@
Psionic Roshambo:
The problem with X party blocked X bill that would have prevented X is that yes the bill probably would have worked great, buuuttt they put XYZDCBG in said bill as an attempt to sneak things in that tend to be completely unrelated to the original bills intent. It sucks because if they would just do a single thing they could probably get something done...
-
@
Psionic Roshambo:
But congressman X needs to have government funding for his cousins unicycle business
-
-
-
-
-
-
Rotflmao