How can I update a pi zero trough toolbox?
The chip don’t have the USB C port
The chip don’t have the USB C port
Last edited by Ganesha0112,
place update.bin in sd root folderHow can I update a pi zero trough toolbox?
The chip don’t have the USB C port
Picofly AIO Threadhey guys i found this thread and i didn't follow it at all but i'm really intersted in it, someone has done a guide for doing this ?
or i need to read all of this ?
if there isn't a official guide to follow i'll try to do one by myself and maybe share it with the admins
thx to everyone
dang ninja XDplace update.bin in sd root folder
open picofly toolbox
update
reboot
Post automatically merged:
Picofly AIO Thread
here everythign u ned to know
Works on all models.Guys did anyone use 0.10 wire for mod and does it work as I think it's to thin?
Can someone confirm that works.
yes it works for everything except the wires from caps to mosfet if u use wires installing the mosfetGuys did anyone use 0.10 wire for mod and does it work as I think it's to thin?
Can someone confirm that works.
That’s what I was wondering, too.I often replace m92t36 so was thinking of using another 3.3v point so to not run wires around m92 incase it ever needs to be replaced
The emmc board has a 3.3v point that I guess sx core and hwfly clones use with the solderless chips
View attachment 363672
That’s what I was wondering, too.
And for the same reasons.
@ follow
yes u can also use it from the emmc i have done it on my v2 so no problem thereI often replace m92t36 so was thinking of using another 3.3v point so to not run wires around m92 incase it ever needs to be replaced
The emmc board has a 3.3v point that I guess sx core and hwfly clones use with the solderless chips
So what do you recommend to connect the caps to the mosfet ?yes it works for everything except the wires from caps to mosfet if u use wires installing the mosfet
i would recommend using flex cableSo what do you recommend to connect the caps to the mosfet ?
I used AWG36 except for 3.3v/GND (AWG30). No issues at all.Guys did anyone use 0.10 wire for mod and does it work as I think it's to thin?
Can someone confirm that works.
Starting with 2.6 alpha, you can just update the chip using a special payload, no need to use USB.Is there a way we could incorporate the data lines from the switch to the picofly, and have a sort of update mode so we can flash the pico with the switch usb-c, that way we don’t need to open the switch and re add the usb-c every new update?
MOSFET or flex? If MOSFET with cable or direct to cap?I used AWG36 except for 3.3v/GND (AWG30). No issues at all.
Post automatically merged:
Starting with 2.6 alpha, you can just update the chip using a special payload, no need to use USB.
However u want to do itMOSFET or flex? If MOSFET with cable or direct to cap?
same as the for every other board 47OHMCan someone tell me the value of the cmd resistor on the OLED?
I used wires to the MOSFET, MOSFET is sitting next to the CPU. See here, before it glued it down: https://gbatemp.net/threads/picofly-a-hwfly-switch-modchip.622701/post-10113097MOSFET or flex? If MOSFET with cable or direct to cap?
I used wires to the MOSFET, MOSFET is sitting next to the CPU. See here, before it glued it down: https://gbatemp.net/threads/picofly-a-hwfly-switch-modchip.622701/post-10113097
The one on the board side.ot the one on the rp2040 47OHM.Pinout for XIAO2040
@Adran_Marit if u want to add this to
im gonna try to add itsybitsi and pico later when i have more time
View attachment 363678
Post automatically merged:
same as the for every other board 47OHM