the Flex is v1 with 1 MOSFET, the motherboard is oledWell lucky u :-) I tried a pled first with 1 MOSFET didn't work after that is only went with 2 cause I didn't wanna fuck around with it.
the Flex is v1 with 1 MOSFET, the motherboard is oledWell lucky u :-) I tried a pled first with 1 MOSFET didn't work after that is only went with 2 cause I didn't wanna fuck around with it.
Yeah I figured that after I posted my original textthe Flex is v1 with 1 MOSFET, the motherboard is oled
Me too, I've always used two MOSFETs. Just recently, I switched "no pun intended" into one and it seems to be working.I've always used 2 MOSFETs on everything just cause it worked , tried it one or 2 times with one but I couldn't get it to glitch.
But why would u only want to reball to these points? doesnt make any sense, just reball it as a whole and be done with itHi, Anyone had experience and succed in emmc reballing but [ ONLY ] using these point. As i see only those are connected through vias.
View attachment 381438
Two reason because it will be faster and also i dont have the stencil.But why would u only want to reball to these points? doesnt make any sense, just reball it as a whole and be done with it
well i always to with stencil and paste , that would even make it more work.Two reason because it will be faster and also i dont have the stencil.
Hi, Anyone had experience and succed in emmc reballing but [ ONLY ] using these point. As i see only those are connected through vias.
View attachment 381440
here you go https://vi.aliexpress.com/item/1005004456312332.htmlI try to find link on aliexpress on green adapter on emmc, but can't find even once. I remembered theres seller on aliexpress like 1-2 month ago.
Yup .. i redid the pic.. it cover all rounded pads now, and left out the non rounded one.. Will it work now?I bet your emmc won't be super excited about not getting gnd and vccq
This will work no doubt but only if you manage to put in place perfectly, and it is much more difficult to achieve this type of installation if you are using only couple of points underneath.Yup .. i redid the pic.. it cover all rounded pads now, and left out the non rounded one.. Will it work now?
View attachment 381443
My resistors from ali arrived today. Added 100 Ohms to dat0/cmd. Slow EMMC issue is gone and booting to CFW/OFW works just fine now! Thanks a lot for the tip, even though it's mentioned in the guide, I would have probably not figured it out.if you get black screen when booting ofw then the software on the sd card is not the problem. I would try adding stronger resistance on dat0/cmd. I normally use 100 ohms each to avoid ofw issues.
I have checked your oled pinout, it seem the orange pin is just suitable for D and yellow next to it for gnd. both pin is huge and got big cap that easy to soldering. Have you tried it, maybe next time I would give it a shotv1
View attachment 381311
Lite
View attachment 381312
v2 (From @raksmey1231)
View attachment 381313
oled (From @raksmey1231)
View attachment 381314
This thread spawned and blew up because of some dude off craiglist...... Sweet!!!Got this offer on a local craiglist:
View attachment 341370View attachment 341371 View attachment 341369
The seller says it's a new RP2040 Picofly based version modchip for Switch Lite and Oled, only.
What do you think about it, looks like it's a clearly fake, am I right?.. Or not?
This thread spawned and blew up because of some dude off craiglist...... Sweet!!!
Yeah props to that guy! Does anyone know if the firmware Rehus is graciously developing for us is in any way related to the original craigslist discovery? Or was the Picofly firmware we use a result of starting from scratch? Either way it's very impressive and I can't say thank you enough to everyone involved!This thread spawned and blew up because of some dude off craiglist...... Sweet!!!
Yeah props to that guy! Does anyone know if the firmware Rehus is graciously developing for us is in any way related to the original craigslist discovery? Or was the Picofly firmware we use a result of starting from scratch? Either way it's very impressive and I can't say thank you enough to everyone involved!
I meant that the Picofly was first discovered on Craigslist. Check first post of this thread.what discovery did craigslist make?