@rehius sorry for ping. I have a question regard an issue i'm having with picofly. I have an Oled with RP2040 on FW 2.75 and OFW 17.0.0. Everything is fine but sometimes my chips panics and gives one of these errors:
=**= eMMC write failure - comparison failed
=*=* eMMC write failure - write failed
=*== eMMC test failure - read failed
Sometimes after some reboots or Power Off/On My switch boots to hekate but sometimes it takes a lot of reboots, some days ago it did the error and only the next day it booted just to give me the error once. Now i'm in cfw and i tried some 5 reboots and they're all successful but this happens randomly and when it does it's so boring. I have picofly since may and it happened almost everymonth but only twice it happened that i had to wait a whole day to make it work. Most of times it just happens for 5 reboots max.
Is this a bug or like a compatibility issue because i have SK Hynix EMMC and iirc they're not the best out there.
=**= eMMC write failure - comparison failed
=*=* eMMC write failure - write failed
=*== eMMC test failure - read failed
Sometimes after some reboots or Power Off/On My switch boots to hekate but sometimes it takes a lot of reboots, some days ago it did the error and only the next day it booted just to give me the error once. Now i'm in cfw and i tried some 5 reboots and they're all successful but this happens randomly and when it does it's so boring. I have picofly since may and it happened almost everymonth but only twice it happened that i had to wait a whole day to make it work. Most of times it just happens for 5 reboots max.
Is this a bug or like a compatibility issue because i have SK Hynix EMMC and iirc they're not the best out there.
- Joined
- Sep 2, 2020
- Messages
- 1,333
- Trophies
- 0
- Age
- 39
- Location
- TORONTO
- Website
- form.jotform.com
- XP
- 2,273
- Country
You didnt tell the full story. How was the dat0 connect to rp2040,adapter or permanent soldering?
i don't know cuz i didn't install the chip, i sent it to an installer but iirc it is adapter
Hello everyone 1st time using Picofly and does this then straight to ofw. Unless I'm being silly I am not seeing my error on the led it's flashed with 2.75. used hwfly before all this never had a problem. Any help? I've checked my soldier joints before UV masking and all looked ok. Before I break all that wanna see if anyone knows the error to pin point locwtion. 47R0 resistors used.
I have the following problem with a completely new Oled.
I've done a lot of conversions but never had a problem like this.
A Raspberry tiny with firmware 2.73 is installed.
Dat0 is an adapter not soldered.
The Switch starts normally in Hekat but not in OFW, the Nintendo logo appears and then nothing.
It was no problem creating CFW. Athomspäre starts normally and you can install games.
When you start the OFW nothing works, only a hard reset then it starts up in Hekate. If you restart the CFW via the menu
you want to get back to the OFW boot logo... Hard reset then go to Hekate.
Very strange.
Error code is the following:
short short long is called
No eMMC block 1 read (should not happen)
There are no error messages in Benchmarck or when reading out. All OK.
What should I do?
I've done a lot of conversions but never had a problem like this.
A Raspberry tiny with firmware 2.73 is installed.
Dat0 is an adapter not soldered.
The Switch starts normally in Hekat but not in OFW, the Nintendo logo appears and then nothing.
It was no problem creating CFW. Athomspäre starts normally and you can install games.
When you start the OFW nothing works, only a hard reset then it starts up in Hekate. If you restart the CFW via the menu
you want to get back to the OFW boot logo... Hard reset then go to Hekate.
Very strange.
Error code is the following:
short short long is called
No eMMC block 1 read (should not happen)
There are no error messages in Benchmarck or when reading out. All OK.
What should I do?
It seems that most of the people with problems think that people on the forum is mind readers.
You need provide more info and pictures if you want help, remember that there is thousands of people who dont have a problem with picofly.
ask yourself, could it be that there is some problems with my install?!
Yes, to 99,9%.
It’s like if i would ask you, whats wrong with my car and not provide more info…
Long time lurken here but been moddings consoles/repairing electronics for 25 years and i have f ed up more than once in these years. Nobody is perfect, we all do it sometimes
You need provide more info and pictures if you want help, remember that there is thousands of people who dont have a problem with picofly.
ask yourself, could it be that there is some problems with my install?!
Yes, to 99,9%.
It’s like if i would ask you, whats wrong with my car and not provide more info…
Long time lurken here but been moddings consoles/repairing electronics for 25 years and i have f ed up more than once in these years. Nobody is perfect, we all do it sometimes
Sorry but i descripe the problem very well i think? is there anybody that have this errorcode? What "could" it be.
Maybe a user had same issue before
So what are your resistor values? Have you tried changing them?
Common problem if you cant boot ofw.
So no there is not enough information provided and also, why are you running an old firmware? Tried with 2.75?
the resistors are 47ohms on the tiny board they are fix installed. i check the values.
The Firmware ist 2.73. this is what a already istalled.
Yes, and this is the most common problem on the forum. If you just search and read a little bit you would know what to do.
Yes, you can update the firmware and you should.. the one you have is old…..
and no not ... i never see a post like mine with this error code. Emmc Info is okey no "slow mode".
CFW runs normal but OFW doesnt boot.
Strange is the error code. short short long.
i installed a many picolfy and HWFly and have never this promlems
Sorry but you are wrong, they have not rolled back from 2.75
https://github.com/rehius/usk/releases
And the solution is to change to 100ohm per the guide.
So you are welcome for the spoonfeeding
And if you even cant search the forum, maybe you shouldnt install for others.
Just saying, prove me wrong and show us your install pictures
https://github.com/rehius/usk/releases
And the solution is to change to 100ohm per the guide.
So you are welcome for the spoonfeeding
And if you even cant search the forum, maybe you shouldnt install for others.
Just saying, prove me wrong and show us your install pictures
Similar threads
-
-
-
-
-
-
-
@
BigOnYa:
I want a handheld gaming system with a tablet sized screen, like a 8 or10" screen, with controllers that can detach like the Switch. -
@
BakerMan:
@BigOnYa i was legitimately trying to scratch my leg, this is reminding me of that cylinder post -
@
Scarlet:
I don't see the buzz about a square screen personally. I think there will be a review on the site within a few weeks though if you are interested.+1 -
@
Scarlet:
I've put down the money on the Odin 2 Mini since I just love that Vita form factor. Loved the power of the Odin 2 but the size always put me off, this one seems exactly what I've been wanting.
-
@
K3Nv2:
I don't care about the square screen it's just nice to hold something you don't have to stretch your arms a foots length -
@
K3Nv2:
All these things expecting to be super huge is overrated just run a type c cable to your TV if you want a big display or in my case screen mirror it
-
@
BigOnYa:
On the go tho I meant, I use my 10" tablet and a Bluetooth controller for retro gaming while sitting on my porch or on long car rides sometimes. Easier on my eyes than the Switch screen.
-
@
K3Nv2:
My point is we already have enough shit with big displays having something pocketable with up to ps2 would be fine on the go+1
-
@
Psionic Roshambo:
Ken unless the games are made for that screen size most suck on a screen that size... Having a square screen and being brighter and higher res helps but it's not a cure all, text is tiny bullets are tiny, your.... Well lol -
-
-
-
-
-
@
Psionic Roshambo:
I swear if I hear "I don't usually do this on the first date" on more time... I am going to start counting
-
-
-
-
@
Psionic Roshambo:
No no continue, I hear these things women say so often I decided to start counting
@
Psionic Roshambo:
No no continue, I hear these things women say so often I decided to start counting