The sdcard is the weakest link of the Switch. Swapping them in and out will eventually break the reader. Readers are cheap so no big deal but it's a pain if you can avoid it.Can you use multiple SD cards for games and emunand?
I was just thinking about having more games on hand but it's not essential and I would rather not have to keep replacing partsThe sdcard is the weakest link of the Switch. Swapping them in and out will eventually break the reader. Readers are cheap so no big deal but it's a pain if you can avoid it.
What are you looking to do? Their might be an alternative solution...
I was just thinking about having more games on hand but it's not essential and I would rather not have to keep replacing parts
hekate ini looks fine tbh. but could add this for shits n gigsNo tinfoil disabling the emummc did sounds like a stretch.
Ok, that's good to hear.
Here's the ini, it's the one they got in the rentry guide
Code:[config] autoboot=0 autoboot_list=0 bootwait=3 backlight=100 autohosoff=0 autonogc=1 updater2p=0 bootprotect=0 [Atmosphere CFW] payload=bootloader/payloads/fusee.bin icon=bootloader/res/icon_payload.bmp [Stock SysNAND] fss0=atmosphere/package3 stock=1 emummc_force_disable=1 icon=bootloader/res/icon_switch.bmp
[config]
autoboot=0
autoboot_list=0
bootwait=3
backlight=100
autohosoff=0
autonogc=1
updater2p=0
bootprotect=0
[Atmosphere CFW]
emupath=emuMMC/RAW1
emummcforce=1
payload=bootloader/payloads/fusee.bin
icon=bootloader/res/icon_payload.bmp
[Stock SysNAND]
fss0=atmosphere/package3
stock=1
emummc_force_disable=1
icon=bootloader/res/icon_switch.bmp
Thnx, I'm still really confused how it managed to disable the emummc but it's only happened once so far and since no one seems to know about that part I'll probably just start over from scratch with my sd card if it happens againhekate ini looks fine tbh. but could add this for shits n gigs
Code:[config] autoboot=0 autoboot_list=0 bootwait=3 backlight=100 autohosoff=0 autonogc=1 updater2p=0 bootprotect=0 [Atmosphere CFW] emupath=emuMMC/RAW1 emummcforce=1 payload=bootloader/payloads/fusee.bin icon=bootloader/res/icon_payload.bmp [Stock SysNAND] fss0=atmosphere/package3 stock=1 emummc_force_disable=1 icon=bootloader/res/icon_switch.bmp
Sounds like you might have been down rev quite a bit. You shouldn’t have any references to fusee-secondary in 1.x.x. You should be using fusee.bin rather than fusee-primary. There are a few changes you will need to tweak.hey guys, tdy i've tried to update my nintendo switch to fw 14.1.2 along with atmosphere 1.3.2 , when i boot into fusee-primary the screen showed "Fatal error: Failed to stat stage2 (atmosphere/ fusee-secondary.bin)!"
what should i do cuz i've never used fusee secondary. thanks in advance.
oh my gosh i completely forgotten i have to use fusee.bin instead of fusee primary. it works now thank you so much!Sounds like you might have been down rev quite a bit. You shouldn’t have any references to fusee-secondary in 1.x.x. You should be using fusee.bin rather than fusee-primary. There are a few changes you will need to tweak.
Take a look here:
https://rentry.org/MigrateToAtmosphere1_0_0
e: you should also update you’re ban protection to make use of exosphere and dns:mitm
https://rentry.org/ExosphereDNSMITM
So I'm liking the idea of installing games via a USB c dongle, how do I dump my games to my pc with all updates so I can put them on a thumb drive and install on the go
No, emuMMC can be setup at anytime and anywhere as long as you have the space on the SD card to make it.Do I need to do a fresh install if I want to install emuNAND? I already have sysNAND that install on it months ago.
Its called maintenance mode and you enter it by holding volume - and + when turning the console on.I think I had the same problem with smash. Someone told me to soft reset switch. Something like that. U have to hold some buttons for some time. And after that smash worked perfectly.
Have two switch lites I am looking to install some hwfly chips into. There are so many versions I am not sure what ones to get. Not sure if there is a major resources I am missing on these or what. Any link would be appreciated.
Nope. Just let it charge. On low charge switch do not display charging icon.Switch, first revision, latest Atmo, no auto RCM turned on - I never turn off the system, but yesterday I've forgotten to charge it and today it won't turn on. Left it to charge for now, but so far it doesn't even show the charging icon. Should I be worried, or let it just sit for a while?
That's practically an oxymoron there. Was it in sleep mode, and it won't wake up? Anyway, plug directly in charger (not dock) and let it charge for a while.I never turn off the system ... and today it won't turn on.