original build hekate/atmosphere i can´t configure hekate_ipl to go emummc or stock, and builds like "sthetix hats" or "Next" i can but console stuck in sleep mode.May as well explain your problem
original build hekate/atmosphere i can´t configure hekate_ipl to go emummc or stock, and builds like "sthetix hats" or "Next" i can but console stuck in sleep mode.May as well explain your problem
original build hekate/atmosphere i can´t configure hekate_ipl to go emummc or stock, and builds like "sthetix hats" or "Next" i can but console stuck in sleep mode.
im using emunand, what im trying is can access stock and emunand throught Lauch button on hekate,I believe it been told to use Emunand for Picofly user, People with non picofly like HWFLY modchip doesn't have this problem.
im using emunand, what im trying is can access stock and emunand throught Lauch button on hekate,
doesnt not work i choose boot options and reload hekate, i have to download latest atmosphere and latest hekate only? maybe something is missingUse these line for emunand and stock
[CFW (EMUMMC)]
fss0=atmosphere/package3
kip1patch=nosigchk
emummcforce=1
icon=bootloader/res/emummc.bmp
{}
[Horizon]
fss0=atmosphere/package3
stock=1
emummc_force_disable=1
{}
doesnt not work i choose boot options and reload hekate, i have to download latest atmosphere and latest hekate only? maybe something is missing
Friends do you have a good hekate/ams build for picofly, i have issues with original ams and builds like hats
Might be a picofly thing, it work fine for non picofly user like trinket m0, HWFLY
Might be a picofly thing, it work fine for non picofly user like trinket m0, HWFLY etc.
i used PiCoFly FW2.5+unlock firmware for the chip and installation im really sure is good.It works for other people so I'm guessing it's your firmware on the chip or installation
You are correct! I went with what sthetix had on his video. However, you had me wondering since it’s been a while since I have done an install. My personal OLED read .428. Actually, all of my points were under .500. Will leave the high end in my post since I know for a fact I’ve seen higher plus in the video sthetix does too.Keep in mind that data 0 connection could have good readings and still not work. I find 420ish red probe on ground always working. 500ish is kinda high and can work on some but if you have any issues on re assemble I would check this again.
it's small but it's good to know so that the lenth of the connection is a factor..The consensus on this is no. I’m not fully sure but I think that the longer the source and drain leads are the likely hood it will not glitch/train…. There is a reason SX and HWFLY have the mosfet so close to the APU.
What are the files supposed to be in the microsd card? (This may be dumb but i never got into switch hacking since now i got a reason)
This is a Pikofly AIO Thread/Tutorial.
This information has been pulled from other threads and forums on this site, I haven't done anything except compile it in this one thread.
All credit goes to those who worked on all the relevant information and stuff.
First things First; I not not endorse piracy and those who released the firmware don't either so this is for home-brew use only.
DOING THIS MODIFCATION TO YOUR SWITCH MAY CAUSE PERMANENT DAMGE. I RECOMMEND YOU HAVE THIS DONE BY A PROFESSIONAL INSTALLER
DISCLAIMER! Me nor any of the other temp members who helped make this happen will be held liable to any damage you cause your console in attempting to mod it. Professional installation is recommended for this mod.
Just because a mod is cheap doesn't mean it's easy. - Trust me I learnt the hard way - Adran 2023
General InformationInstallation overviewImagesCredits
RequirementsHintsLED IndicatorsFAQ's
- RP2040-Zero
- SMD 8050 47 to 50 ohm Resistors
- Mosfet (IRFHS8342 MOSFET) or cpu flex cable (lite flex for lites, v2 flex for v2 mariko etc etc)
- switch (duh)
- Wire
- RP2040 Firmware (direct Link)
Changelog: Added Erista v1? diagram
P.S More formatting and information to come
What are the files supposed to be in the microsd card? (This may be dumb but i never got into switch hacking since now i got a reason)
This is for people that have micro-soldering skills and tools, like the iphone board repairs.So be aware of that.hello,
just want to know what the experienced people have conclude for moding the oled switch.
what hardware is needed
RP 2040
how hard is it to install as a DIY .
I missed that partThis is for people that have micro-soldering skills and tools, like the iphone board repairs.So be aware of that.
exteremly hard for the average user.hello,
just want to know what the experienced people have conclude for moding the oled switch.
what hardware is needed
RP 2040
how hard is it to install as a DIY .
Thanks
Do i need to do the rcm thing like it just makes the switch unpathched or it does something automatic (or another way)?You will need the latest hekate+ atmosphere
no, and if you enable auto RCM on a patched unit, you could end with a Brick.Do i need to do the rcm thing like it just makes the switch unpathched or it does something automatic (or another way)?
Ok then it's loading atmosphere automatically ?no, and if you enable auto RCM on a patched unit, you could end with a Brick.
It will load whatever you have as payload.bin from the sd cardOk then it's loading atmosphere automatically ?