Recent content by deathnotejacoby

  1. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yes i used DATA0 Adapter for solder. I dont wire direclty. i dont heat the eemc. i wondering that the diode value is now 0,42V and 0,47V. the error code is long short. =* yellow 1711020711 Hey, i change the 4,7kOhm resistor ... now it is working .... next question. sometimes the process takes...
  2. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello, I have already converted many OLEDs, but there are always problems. Currently, I have encountered a problem again. I've had this problem twice with the Nx-Instinct V6 OLED Modchip. However, at that time, I was still working with flex PCBs. Now, I'm wiring all contacts individually without...
  3. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    is these a via next to the Dat0? I found this picture from a another old thread about dat0 alternative. I dont really like the way to take the data signal from the balls of the emmc. Sometime i have bad Dat0 Adapter.. Did anybody try to drill?
  4. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    no video sure. Only used the update.bin file from github. With normal usb upgrade it works fine with 2.75...
  5. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    in this case yes. 0201 is the size.
  6. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Do you upgrade your console with picoflytoolbox? I upgrade it from 2.73 to 2.75. It was succesfull (this was wrote after the upgrade) after that i restarte the cosole. Than i start ofw and get a error message. Partition table is empty Without chip i get a purble screen. i check the firmware...
  7. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    I dont have a emunand. I only start cfw with fuse.bin. I dont create a dump. i´m wondering that after the upgrade was the emmc delted. It was upgrade finished and then reboot to hekate. the cables are still ok.
  8. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    i dont have a backup .. damn .. that it i can used it for paperweight. And maybe the only solution was a 200ohms on Dat0 .. maybe .. Why did this happen? from upgrade to 2.73 was no problem anymore from 2.73 to 2.75 it deleteds your eemc?
  9. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello, I try to change the resistoor from 47ohm to 100ohm and it was still the same. After start ofw Nintendo Switch boolgo showing then nothing. CFW is working. After the tip to upgrade from 2.73 to 2.75 the switch want boot anymore. It was showing a error message. The Partition table is...
  10. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    i will try it. very sorry
  11. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    hey, i dont have "slow mode" problems i dont get the message benchmarch was also without errors . i have the 2.73 on github .. were is the 2.75? very sorry for my ignorance 1700258561 thank you ... i installed a rp tiny .. never need to change the resitors .. only with 2040
  12. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    and no not ... i never see a post like mine with this error code. Emmc Info is okey no "slow mode". CFW runs normal but OFW doesnt boot. Strange is the error code. short short long. i installed a many picolfy and HWFly and have never this promlems
  13. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    sorry is it not... they rolled back to 2.73 .. github
  14. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    the resistors are 47ohms on the tiny board they are fix installed. i check the values. The Firmware ist 2.73. this is what a already istalled.
  15. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Sorry but i descripe the problem very well i think? is there anybody that have this errorcode? What "could" it be. Maybe a user had same issue before
See more
General chit-chat
Help Users
    Bunjolio @ Bunjolio: +2