Hacking My Nintendo Switch Isn’t working after using ChoidujorNX

[NeoSlyde]

Where would I find this

--------------------- MERGED ---------------------------

Oh yeah by the way I'm trying to go to firmware 6.0 instead of 5.1 because I burnt the fuses

--------------------- MERGED ---------------------------


Yeah I did

--------------------- MERGED ---------------------------

Would this help with my problem or is this thread something else
https://gbatemp.net/threads/how-to-...nofficially-without-burning-any-fuses.507461/

Try to reuse a jig to boot rcm
I think auto rcm got disabled

 

[Sylvan]

Try to reuse a jig to boot rcm
I think auto rcm got disabled

I tried that too but it didn’t work either

 

[XaneTenshi]

I tried that too but it didn’t work either

I've read the various posts here to try and get a grip on your situation. There is not much we can do until you manage to get it into RCM mode. I've gathered that you removed AutoRCM using Hekate, so you need to get into RCM manually. Make sure the jig is properly inserted and then press and hold the Vol + button and then press the power button once. Then connect it to your PC and see if TegraRCMGui can detect it. Otherwise go to devices and printers and see if it shows up either as APX or Linux UMS (something).

Also, I have two questions for you. You did install AutoRCM when you downgraded using ChoiDujourNX and then removed it using Hekate, right?

Did you ever accept the controller update when you updated to 6.1.0?

EDIT: If the above doesn't work, try to charge the Switch for a couple hours (something like 4+) and try again. I'm just wondering if at some point, your battery drained completely.

 

[Sylvan]

Yes to the first question and no the second question and also I will try all of this

 

[Paperjin]

I was in a similar situation as you, it's even more difficult since you can't boot to HOS.
You're not triggering rcm, just make sure you can get into it and you should be able to continue

 

[Sylvan]

Will I have to charge the switch for a few hours before trying all of this

 

[The Real Jdbye]

Will I have to charge the switch for a few hours before trying all of this

Couldn't hurt.

 

[Sylvan]

Couldn't hurt.

Ok then I will

 

[Sylvan]

I did what all of you said charge the switch for a few hours then try putting it into RCM with the jig then I hold the power button and volume + button at the same time and then I connect it to the computer and it doesn’t say it’s in RCM and also the switch doesn’t show up in devices and printers as APX or Linux UMS. I even hold the power and + volume at the same time when I’m connected to the computer and it still doesn’t show it in RCM or in devices and printers

--------------------- MERGED ---------------------------

 

[Don Jon]

you hold the + button and than press power, while holding the + button.
not the other way around

 

[Sylvan]

you hold the + button and than press power, while holding the + button.
not the other way around

That didn’t work either

 

[stussy1]

That didn’t work either

Just a heads up you sure your switch is turned off sounds to me it's still on when trying to manually get into rcm.

If all fails disconnect battery on switch wait a minute or 2 then reconnect it then rcm it.

 

[eskinner3742]

Try booting into maintenance mode to update:
https://en-americas-support.nintend...to-update-nintendo-switch-in-maintenance-mode

 

[SgtP3pp3r]

Just as additional input, make sure you try connecting the switch to different USB ports, or if you have a USB OTG cable and an android device, try using that to load the payload. My switch seems to have damaged one of my USB ports on my laptop, it doesnt work well anymore (stopped working while loading a payload, works intermittently since).
Also, check in a dark room if the screen is coming on when you press the power button, or if the switch is not being powered on at all, if it isnt then try charging the switch for an even longer period of time, and try using the jig afterwards.
If it is coming on and none of that works, then let the battery drain completely, and charge it AFTER it has drained completely and try again.
*Edit: Try using a different USB-C to A cable

 

[Sylvan]

Just a heads up you sure your switch is turned off sounds to me it's still on when trying to manually get into rcm.

If all fails disconnect battery on switch wait a minute or 2 then reconnect it then rcm it.

I did what you said and it didn’t work

--------------------- MERGED ---------------------------

Try booting into maintenance mode to update:
https://en-americas-support.nintend...to-update-nintendo-switch-in-maintenance-mode

That didn’t work either

--------------------- MERGED ---------------------------

Just as additional input, make sure you try connecting the switch to different USB ports, or if you have a USB OTG cable and an android device, try using that to load the payload. My switch seems to have damaged one of my USB ports on my laptop, it doesnt work well anymore (stopped working while loading a payload, works intermittently since).
Also, check in a dark room if the screen is coming on when you press the power button, or if the switch is not being powered on at all, if it isnt then try charging the switch for an even longer period of time, and try using the jig afterwards.
If it is coming on and none of that works, then let the battery drain completely, and charge it AFTER it has drained completely and try again.
*Edit: Try using a different USB-C to A cable

That also didn’t work

 

[jammybudga777]

Tbh I thought if you downgraded after burning fuses it's bricks? At least that's what I thought

 

[Sylvan]

Tbh I thought if you downgraded after burning fuses it's bricks? At least that's what I thought

Does it

--------------------- MERGED ---------------------------

Could I send my switch to a company for them to fix it