Picofly AIO Thread

[Arakon]

Right in the firmware github linked on the first page of this thread.

 

[Danook28]

For the oled must use v3 Flex Cable or another type. Thank you

 

[cicci084]

Hi guys, How i run picofly toolbox from hekate?

 

[linuxares]

Hi guys, How i run picofly toolbox from hekate?

https://switch.homebrew.guide/using...ding-other-fusee-gelee-payloads-within-hekate

 

[cicci084]

https://switch.homebrew.guide/using...ding-other-fusee-gelee-payloads-within-hekate

I run the update (a second was enough).
Is there any way to know the installed firmware version?
If so, where can I check it?
Thanks for the support.

 

[linuxares]

I guess check the boot logo. Does it have a raspberry with wings?

 

[Dee87]

I run the update (a second was enough).
Is there any way to know the installed firmware version?
If so, where can I check it?
Thanks for the support.

go pico toolbox and see what info has to say

 

[MXRD4K1LL4]

[]

 

[cicci084]

I guess check the boot logo. Does it have a raspberry with wings?

Yes, yes, i just updated to fw 2.61 via picofly toolbox.

But it was to understand, I wanted to know how to check which firmware is installed.

 

[Dee87]

Yes, yes, i just updated to fw 2.61 via picofly toolbox.

But it was to understand, I wanted to know how to check which firmware is installed.

pico fly toolbox and then info

 

[naldo29]

Anyone got a v2 schematic? Ive seen different instalations done and i dont know which one would be the best or the easiest ive seen people do the instalation with wires on the emmumc and people who have done it without putting wires on the emmumc? Anyways im just a bit confused by it all, any help thanks!

 

[cicci084]

pico fly toolbox and then info

Stuck on the screen:

Reading firmware info...
Press any Key

Nothing information

 

[Dee87]

Anyone got a v2 schematic? Ive seen different instalations done and i dont know which one would be the best or the easiest ive seen people do the instalation with wires on the emmumc and people who have done it without putting wires on the emmumc? Anyways im just a bit confused by it all, any help thanks!

there are shematics on the first page only us connections on emmc connector if u know what u are doing otherwisen use different pinouts

Post automatically merged: Apr 10, 2023

Stuck on the screen:

Reading firmware info...
Press any Key

Nothing information

did u reboot?

 

[naldo29]

there are shematics on the first page only us connections on emmc connector if u know what u are doing otherwisen use different pinouts

Post automatically merged: Apr 10, 2023

did u reboot?

sorry im literally blind or maybe im a dumbass but i cant find the images contaning the pinouts for the v2, could you link it if its possible thanks!

 

[MXRD4K1LL4]

This is a Pikofly AIO Thread/Tutorial.
This information has been pulled from other threads and forums on this site, I haven't done anything except compile it in this one thread.
All credit goes to those who worked on all the relevant information and stuff.

First things First; I not not endorse piracy and those who released the firmware don't either so this is for home-brew use only.

DOING THIS MODIFCATION TO YOUR SWITCH MAY CAUSE PERMANENT DAMGE. I RECOMMEND YOU HAVE THIS DONE BY A PROFESSIONAL INSTALLER

DISCLAIMER! Me nor any of the other temp members who helped make this happen will be held liable to any damage you cause your console in attempting to mod it. Professional installation is recommended for this mod.

Just because a mod is cheap doesn't mean it's easy. - Trust me I learnt the hard way - Adran 2023

FW Changelog

General InformationInstallation overviewImagesCredits

1. 
   

   RequirementsBoard Pinout ListHintsLED IndicatorsFAQ's

   1. 
      
      • RP2040-Zero
      • SMD 0805 47 to 50 ohm Resistors
      • Mosfet (IRFHS8342 MOSFET) or cpu flex cable - I personally recommend - (lite flex for lites, v2 flex for v2 mariko etc etc)
      • switch (duh)
      • Wire
      • RP2040 Firmware (get the latest firmware from here FW 2.6 onwards doesn't need unlock)
   2. 
      !!!!PinOut for Other Boards!!!! (resistors / mosfets are still required)
      
      
      
   3. 
      
      
   4. 
      
      
   5. 
      
      
   
   
2. 
   
   
3. 
   

   Mosfet ImagesSolder Points

   1. 
      
      
      
      
      
      
   2. 
      
      
      
      
      
      
      
      
      
      
   
   
4. 
   
   

Changelog:
8-April-2023
Added FW 2.61 and changelog

7-Apr-2023
- Fixed size Mistake
- Added Firmware 2.6Alpha
-added Firmware 2.6a changelod and more board support pinout.

29-mar-2023
- Added link to Toshiba Firmware for rp2040
- Added alternative mosfets
- Added Erista (patched) diagram

P.S More formatting and information to come

I did everything but when I try booting it the led:
Blue/pink then nothing and then stay on blue, there isn't any sign of life from the switch so what did i do wrong?

Btw the 3.3v resistor got off and i put it back so that's maybe an issue?

 

[cicci084]

there are shematics on the first page only us connections on emmc connector if u know what u are doing otherwisen use different pinouts

Post automatically merged: Apr 10, 2023

did u reboot?

Yes, i have reboot

 

[Dee87]

sorry im literally blind or maybe im a dumbass but i cant find the images contaning the pinouts for the v2, could you link it if its possible thanks!

bra really
https://gbatemp.net/threads/picofly-aio-thread.628951/
images ---->solder points

 

[naldo29]

bra really
https://gbatemp.net/threads/picofly-aio-thread.628951/
images ---->solder points

shit im stupid thanks!

 

[Dee87]

shit im stupid thanks!

atleast u admit it urself Xd

 

[impeeza]

shit im stupid thanks!

who am I to contradict you!