Ok so it kinda looks like something worked, here is the terminal:Yes to have to flash the SD. And after flashing you have to format it with FAT32 and resize the partition
[pico] Changed state: WIIU_STATE_POWERED_OFF -> WIIU_STATE_NEEDS_DEFUSE
Starting... 3224:0
Results:
Winner! 0xf368
01
02
03
04
05
08
09
0a
0b
0c
0d
0e
13
14
15
18
1b
1c
1d
1e
1f
25
88
00
00
[pico] Changed state: WIIU_STATE_NEEDS_DEFUSE -> WIIU_STATE_DEFUSED
[pico] Changed state: WIIU_STATE_DEFUSED -> WIIU_STATE_MONITORING
U▒U▒U▒U▒U▒U▒U▒U▒[Pico] Switching to data mode...
fe 00 02 07 01 00 00 43 46 26 10 00 28 4d 45 4d
32 4d 45 4d 30 50 52 53 48 84 00 00 00 5d 5d 00
01 5d 5d 00 02 5d 5e 00 04 5d 5e 00 08 ef a2 82
d9 01 00 02 00 00 00 00 10 01 00 02 10 5d 5d 00
04 f0 0f ca ff f0 0f ca fa 55 aa 55 aa 55 aa 55
aa f0 0f ca [Pico] Switching to text mode...
beefcafeGPU TV addr: 17500001
GPU DRC addr: 00000000
minute loading
minute was loaded from boot1 context!
Initializing exceptions...
Configuring caches and MMU...
MEM: cleaning up
MEM: unprotecting memory
MEM: mapping sections
MEM: enabling caches
MEM: enabling MMU
MEM: configuring heap
MEM: init done
Interrupts initialized
prsh: Header at 10005a54, PRST at 10007ff0, 1 entries (32 capacity):
0: boot_info 0x58 10008000
crypto support initialized
BSP version: 0x26100028
Board type: CF (0x4346)
Board revision: 0x17
DDR props: size=2GiB (0x0800) speed=0x0002 vendor=U! (0x5521)
Initializing SD card...
sdhc: SDHC 1.0, 48 MHz base clock
sdhc_bus_power(0x300000)
sdhc_bus_clock(25000, 0)
sdhc_bus_width(1)
CID: 77017A2F0415102020434453604A7400
CID: mid=74 name='J`SDC ' prv=16.1 psn=05042f7a mdt=7/2007
CSD: 00800A80FFB76DBD835A5B32007F0000
taac=127 nsac=0 read_bl_len=10 c_size=3829 c_size_mult=7 card size=2008023040 bytes
sdcard_select: resp=700
sdhc_bus_;idth(4)
sdcard: enabling highspeed 52MHz clock (32)
sdhc_bus_clock(52000, 1)
resetting due to error interrupt
timeout dump: error_intr: 0x0 intr: 0x2
sdcard: MMC_ALL_SEND_CID failed with 116
sdcard: could not enable highspeed clock for card, falling back to 48MHz highspeed?
sdhc_bus_clock(48000, 1)
resetting due to error interrupt
timeout dump: error_intr: 0x0 intr: 0x2
sdcard: MMC_ALL_SEND_CID failed with 116
sdcard: could not enable highspeed clock for card, falling back to 25MHz highspeed?
sdhc_bus_clock(25000, 1)
Mounting SD card...
crypto: ~0x000 bytes of OTP loaded; JTAG is disabled (000000e1)
Console is de_Fused! Loading sdmc:/otp.bin...
Failed to load `sdmc:/otp.bin`!
Firmware will fail to load.
Press POWER/Q to continue.
[pico] Changed state: WIIU_STATE_MONITORING -> WIIU_CHECK_IF_POWERED_OFF
[pico] Changed state: WIIU_CHECK_IF_POWERED_OFF -> WIIU_STATE_POWERED_OFF
I also just noticed that a wire came off the Pi Pico, don't know if I defused it before that. Will have to solder that back on. Anything you can gain from this though?
EDIT: Just looked and it's the TP144 port on the motherboard that came off the Pi Pico end.