Hacking Fusee - Launcher Released

[GizmoTheGreen]

I'm sorry this image doesn't make much sense it looks normal unless I'm just blind

Mind clarifying ?

seems like it points out those two pins we need to short are available as test points. so you can short them there, or maybe even install an extra button in your joycon to enter SCM mode whenever

 

[linuxares]

seems like it points out those two pins we need to short are available as test points. so you can short them there, or maybe even install an extra button in your joycon to enter SCM mode whenever

Xecutors new modchip! ;D A modded Joycon

 

[Tomobobo]

seems like it points out those two pins we need to short are available as test points. so you can short them there, or maybe even install an extra button in your joycon to enter SCM mode whenever

I'm sure someone could even put a tiny pc like a raspberry pi in a joycon R so you can just run payloads from the hacked joycon.

 

[TerraPhantm]

No, it was never the idea that you install any patches on the console. It was supposed to be a coldboot that loads cfw from sd.

Gotcha. In that case it's a little inconvenient, though probably not a big deal as long as your battery never runs out. I think I'd probably install a momentary switch in the back of my Joy-con or something

 

[Deleted-442439]

Is pin 9-10 nearest to the screen or the back?

 

[ken28]

does it need to touch any other oin or exactly 9, or is it ok if it touches more then one`?

 

[Deathscreton]

Wonder if this is the Team Xecuter solder-less mod chip, lol

It practically is. They're releasing this flimsy looking 3D printed boarding with two pins and metal in it. What the fuck they needed to go through chinese suppliers for, I have no clue. Probably shitty PR tactics.

 

[MichiS97]

It practically is. They're releasing this flimsy looking 3D printed boarding with two pins and metal in it. What the fuck they needed to go through chinese suppliers for, I have no clue. Probably shitty PR tactics.

You're talking about F0F

 

[Deathscreton]

You're talking about F0F

I stand corrected. Still flimsy.

 

[ehnoah]

Someone maybe has a Picture to Shortcut without opening the Controller?

 

[Sephirosu]

Someone maybe has a Picture to Shortcut without opening the Controller?

The guy with a Mac used a tool to short the joycon. Don't think he opened his up

 

[Tomobobo]

The easiest way which has been said so many times would be to just short the pins on the side of the switch itself, rather than using the joycon. You could take the metal railing off to make it easy, or like failoverflow is teasing, just stick some wire in the holes.

 

[Dmafra]

The guy with a Mac used a tool to short the joycon. Don't think he opened his up

But when you put the joycon on switch they could separate.
It's guarantee short the middle of the pins to be more accuracy !

 

[ken28]

you know those "keys" to unlock the sim trays of modern phones? they seem to be just big enough to touch two pins.

 

[Mnecraft368]

Joycon need to be attached ?

How do you plan to reach the pins inside the joycon rail with the joycon attached...

 

[yardie]

How do you plan to reach the pins inside the joycon rail with the joycon attached...

magic

 

[Mnecraft368]

A guide?

Refer to my post at the end of page 3.

 

[Dmafra]

How do you plan to reach the pins inside the joycon rail with the joycon attached...

Attached when connect to pc.

 

[Mnecraft368]

Would love to try this out but am scared that I will break something.
Knowing me I will short the wrong pins and fry the joycon rail.

 

[Dmafra]

Would love to try this out but am scared that I will break something.
Knowing me I will short the wrong pins and fry the joycon rail.

Almost broken the pin 10 trying to short witch joycon closed.
Rather buy a triwing screwdriver

--------------------- MERGED ---------------------------

Almost broken the pin 10 trying to short with joycon closed.
Rather buy a triwing screwdriver